Like all appliance, your home’s water filter should be examined from time to time. Changing your water filter regularly is a fantastic method to ensure it is in top condition always.
The main issue is how do you clean your water filters? What is the frequency they require changing? What happens if you don’t change them? In this article, I’ll provide you with an excellent guideline on how to change whole house water filter in 7 simple steps.
- 1 What is Whole House Water Filters?
- 2 How to Replace Whole House Water Filter
- 2.1 First Step: Switch Off Water Supply, and Release Water Pressure
- 2.2 Second Step: Pull Casing Out and Clean Up O-Ring
- 2.3 Third Step: Toss Old Filter Out and Clean up the Housing
- 2.4 Step 4: Rub Lubricant to O-Ring
- 2.5 Phase 5: Purchase and Install A New Water Filter Cartridge
- 2.6 Step 6: Fix Casing to Cap
- 2.7 7th Step: Switch the Water Supply On, and then Check the Pressure
- 3 Important Tips Regarding New Filter Replacement
- 4 How Often Do I change a whole House The Water Filter?
- 5 Why You Should Change Whole House Water Filter
- 6 Final Words About How to Change Whole House Water Filter
What is Whole House Water Filters?
Whole-house filtering water are water filtration systems which remove water from every outlet in the home. They are placed within your main supply of water, making every faucet within an area to supply water that is clean.
A faucet filter can be used as an alternative to the entire house water filter. It is mounted on every faucet, and it filters water only from those specific outlets. It can be installed underneath in the kitchen basin and on the counter of a specific room. It is a gravity filter is ideal for the countertop.
With whole-house plumbing filters, each faucet can generate safe water for bathing, cooking and so on.
How to Replace Whole House Water Filter
The steps listed below will help you through how to replace the entire household the water filter. However, ensure that you wear safety gloves and safety glasses to avoid splashes of water from getting into your eyes.
You will also require an empty bucket to change the whole house water filter. Put the bucket underneath the water filter to stop water from spilling onto the floor.
First Step: Switch Off Water Supply, and Release Water Pressure
The first step is to complete cut off the source at the valve or the main water supply. To release pressure, press that red button. Watch out for water popping out when you push the knob to release pressure. Use the pressure release button. You can find it on the filter housing.
Second Step: Pull Casing Out and Clean Up O-Ring
Remove the casing and remove the huge O-ring. The O-ring has the form of a large size and is surrounded by a black plastic band that can be found inside the casing. Clean the ring and then place it back in its original position. If it’s damaged take it off and buy another. Clean also the filter housing.
Third Step: Toss Old Filter Out and Clean up the Housing
Get rid of your old filter, and get rid of it properly. After that then the next step you’ll need to do is to clean the casing by taking out the dirt that has built up in it.
Then, you can make use of the warm water, soap from the kitchen and an absorbent cloth or soft sponge to clean the casing. After that, pour 1/3 of water in the housing and add a small amount of bleach and then wash.
The casing should be cleaned gentle and gently in order not to cause any harm. After you’ve finished you should rinse it two times and allow it to dry.
Step 4: Rub Lubricant to O-Ring
Lubricate the O-ring using the use of silicone grease that is clean as this will assist it to sit correctly within its casing. The use of silicone grease is crucial since it does make the rubber shrink or expand. Reposition the O-ring in its groove. When you place the O-ring in the groove be sure to make it adroitly, otherwise, the seal in the housing may rupture.
Phase 5: Purchase and Install A New Water Filter Cartridge
Replace your water filters. If you decide to purchase an reverse osmosis unit or any other type of water filter, be sure to inspect the housing to see if there is an unidirectional standpipe on the middle of the bottom. It is made up of a circular device that has the short pipe of with a rubber.
It is vital to ensure that the filter is placed correctly on the cartridge for water purification. This is because this device acts as a water source, so the water you use in your home is cleaned there before it is dispersed to the faucets in your home. Be sure to place the filter in the middle on the pipe.
Step 6: Fix Casing to Cap
Change the casing by using your filter by manually screwing it into the cap. Make sure that the filter is at the center of the standpipe. It is possible that you are unable to tell however, the standpipe begins sliding through the opening of the cartridge quickly. Be careful not to tighten the casing, because this could cause it to break.
7th Step: Switch the Water Supply On, and then Check the Pressure
To turn the water supply in place, gently flip the inlet switch slowly to the “on” setting. Be careful since the water may gushe out in a flurry, damaging the housing or ruining the whole unit.
So, in order to make sure you are doing it correctly, turn the handle of the inlet slowly, and then stop the valve for the inlet when it is rushing too fast. Be cautious when changing a complete house filter.
Check the pressure by pressing through the orange knob. Make sure to soak slightly since water will spray out. To prevent water from spraying, cover an oversized towel around the unit prior to releasing the pressure.
Important Tips Regarding New Filter Replacement
After you’ve replaced the filter and sealed the housing, allow the water running, unattended for 6 to 7 minutes. It should run for a few minutes to remove dirt. The reason for this is because the water’s sediments could be leaking into the tap as you replace the filter.
How Often Do I change a whole House The Water Filter?
Typically, the lifetime of the majority of filters is between 1 to 6 months. Pre-filters for sediments are less durable. Post-filters are able to last for nine months or more, while carbon filters last the longest (14 to fifteen months).
There are a variety of ways to tell if your water filter isn’t working correctly. One is the unpleasant smell or taste that you begin noticing in your drinking water. Additionally, the speed and the pressure fluctuate.
The old cartridge can also tell much about the condition of the water filter. If it’s worn out or has become old, you should replace it before the next. However, if it’s fresh and clean it is fine to keep it and keep it for a little longer.
But, these elements below will determine the frequency at which you should change your all-house water filters.
- Their capacity, size, and their type (rated as months gallon sizes)
- The quality of the water used for feeding (higher concentration of impurities) reduces the lifespan of filters and increase the likelihood of replacement)
- Iron content, sediment along with other contaminants.
- Water hardness
Why You Should Change Whole House Water Filter
One of the benefits when you install a complete house filtration system is that you are able to modify it as often as you like. Additionally, the system lets users to change the water level in your house with a single swoop.
It is recommended to buy top-quality water filters cartridges as they are more durable and function more efficiently. Cartridges made of top quality are able to last for as long as 36 months while other cartridges might last only 3 months.
The process of changing your water filter every time is an excellent option for increasing the performance of your water filter. If your filter needs changing, it displays indications such as low water flow, a bad flavor, etc.
If you aren’t sure how to replace the filter housing water filters, consult the manufacturer. Be aware that a malfunctioning filter doesn’t necessarily mean that the cartridge is damaged.
Verify that the cartridge is compatible with the kind of contaminants present in your water. A water screening test at home can assist you in determining the presence of contaminants in your water.
Final Words About How to Change Whole House Water Filter
Change of a complete house water filter is a breeze and can reduce the incidence of water-borne illness within a house. The quality of life improves when we take a bath and drink pure water.
Wear safety glasses while changing the whole house sediment filter. Remember to perform the water screening test in case you notice something odd with the water you drink.
Do you have suggestions or concerns about how to change your whole home water filters? If so, leave a comment or question in the box below!